Abs Replacement Procedure Land Rover Discovery 2

It is essential that replacement wheel bearings are fitted correctly and tightened to the correct torque. Replace the SLABS ECU following procedure 706501 in the RAVE Discovery Series II Workshop Manual.

Add New Key All Key Lost Programming For Land Rover Discovery Sportauto Repair Technician Home

Now the Discovery II has a brake system that if you were to open up the system either for caliper master cylinder repair ABS whatever and you need to bleed the system afterwards there is actually a 3 step procedure on the brake bleeding.

Abs replacement procedure land rover discovery 2. I found I could get it up higher than in the write-up using a narrow block of wood under the ABS body without blocking the shuttle valve which made it very easy to get a small ratchet with a 4mm bit underneath to remove the three bolts. Fitted to vehicles from 1998 to 2004 model years. Disconnect the white ABS connector at the left-hand bulkhead.

DIAGNOSTIC AND REPAIR PROCEDURE. You just unplug the brake lines then the two electrical connections and undo 3 bolts and your good as gold. Land Rover Discovery 2 99-04 OEM ABS Module Switch Repair Kit SWO500030 Wabco Fits.

I replaced my shuttle valve and it took me about 40 minutes. Release ABS sensor grommet and harness from inner wing. INVESTIGATE FAULT CODES AND REPAIR WIRING AS INDICATED.

If the fault continues to return then the replacement of the entire ABS modulator assembly is required. Programming Testing Repair Re-build Re-manufacture. 2 b use single line to rear axle instead of 2 add spliter at axle.

19 19 product ratings - Land Rover Discovery 2 99-04 OEM ABS Module Switch Repair Kit SWO500030 Wabco. Luckily it is also a fairly easy part to replace. MODIFY ENGINE CONTROL MODULE SOFTWARE CAUTION.

Complete with fitted ABS sensor and replacement drive-shaft nut. Land Rover 2005 REPLACE LEFT-HAND FRONT ABS SENSORHARNESS 1. Another way to do it is make up 2 leads with flat spade connectors on each end connect a switch in the middle remove the ABS relay and bridge the 2 terminals for the switched side of the relay then flick the switch when you want the pump to run to push as much fluid out as you want need.

This replacement can cost roughly 2000 USD and should be performed by a trained Land Rover. Wiring faults may be intermittent due to hidden breaks and poor. The shuttle valve switch kit is unlikely to repair the problem but it is a relative inexpensive repair option.

Refer to GTR section 861501 and disconnect the battery ground cable 2. I took the shortest route and removed the shuttle valves by just unfastening the ABS module and raising it up as high as I could. A replacement front wheel hub bearing assembly for either side.

So heres my plan 1. ABS Module Valve Kit - Part SWO500030. At the conclusion of the SLABS ECU installation process it is absolutely.

It is part number TAY10060. Follow the TestBookT4 prompts after ECU replacement. LAND ROVER ABS REPAIR.

Print the booking confirmation email. This complex module named the BCU Body Control Module is the heart of the Discovery series 2 is fitted. Package the Land Rover Discovery ABS pump inside a sturdy box with plenty of packaging material make sure you include your confirmation email in the box.

To gain access to the shuttle valve switch module the abs unit has to be lifted a small amount. Do you have the three amigos cluster of ABS HDC and TC lights on your dash. It can be rectified by replacing the ABS shuttle valve modulator switch assembly SWO500030.

Every module shipped out to our customers has all the pertinent information regarding the repairs done to the module and also any specific repairs or testing required on the vehicle itself before the module is installed. Test Procedure and Instructions for Shuttle Valve Switches Applies To. The part used was a front wheel hub and bearing assembly which comes complete with the ABS sensor.

This is not a problem if you prefer this option then follow the following steps. Our post-repair inspection testing procedure is designed to a standard of quality that is well above the manufacturers specifications. Discovery Series II 99-04.

Withdraw the harness through the aperture into the wheel well. Use same size connections instead of. Land Rover Troubleshooting.

It is even possible without draining the brake fluid as seen in the linked video. Land Rover Discovery 5 out of 5 stars. Thats a relatively low cost part.

Remove existing lines from ABS to rear axle done and make new ones from stainless steel tubing. The new shuttle valve switch module and one of its mounting screws being removed using an allen key. Replace ABS module with simple line spliter.

TestBookT4 may prompt for a System Test andor SLS Calibration. Fill in and submit this test form. And in this video were going to show you one of the features on the new iLAND for the Discovery II.

Please refer to the workshop manual for the proper fitting procedure. Once the three nuts were removed the rubber mounts were taken off and kept safe. We can repair the Wabco ABS control units found in Land Rover Discovery Freelander and Hummer H1 sport utility vehicles.

Then bleed the brakes and last but not least get the 3 abs lights cleared as well as a test book system bleed. The Land rover Discovery 2 BCU which is fitted under the left hand side dashboard behind the passenger glove box on RHD vehicles.

Land Rover Discovery Diesel Sw 3 0 D300 S 5dr Auto Brand New Offer Land Rover